STRICT QUALITY CONTROL SYSTEM

CPE 135A, ACR, and MBS: three PVC impact modifiers for three different jobs
Quick Answer / TL;DR
Need impact strength at low temperature (outdoor profiles, pipes, foam board)? CPE 135A. Need melt strength, faster fusion, and surface finish at high line speed? ACR processing aid. Need crystal-clear transparency in a rigid, impact-resistant part? MBS. Need the best balance of toughness and cost in general-purpose rigid PVC? CPE 135A, most of the time.
Ask a PVC processor "which impact modifier should I use," and the answer is almost always "it depends" — followed by a vendor pitch. The internet is full of articles telling you what each modifier does, but almost none telling you how to choose between them for your specific product and your specific cost target.
That is the gap this article closes. If you already know the mechanisms and just want the selection logic, skip to the Decision Matrix below.
Chlorinated polyethylene (CPE 135A) is a rubbery modifier that forms a fine elastomeric network inside the rigid PVC matrix. When a crack starts, that network absorbs the impact energy and stops it from spreading.
Best at: low-temperature impact, outdoor weatherability, and cost-efficient toughening
Typical loading: 6–12 phr in rigid PVC
Where you use it: pipes, fittings, window profiles, WPC, foam board, cable sheathing
Acrylic processing aids are high-molecular-weight acrylic copolymers. Their main job is not toughening — it is fixing the process: faster fusion, higher melt elasticity, smoother surface, better foam cell retention.
Best at: high-speed extrusion, foam board cell stability, surface finish, transparent sheet
Typical loading: 1–5 phr (processing aid role)
Where you use it: foam board, WPC, high-output pipe/profile lines, calendered sheet
Common confusion: ACR processing aids are different from ACR impact modifiers (often called AIM). Processing aids fix melt rheology; AIMs provide impact strength. When someone says "ACR," ask which one they mean.
MBS (methyl methacrylate-butadiene-styrene) is a core-shell impact modifier. Because its refractive index is matched to PVC, it can add impact strength without clouding the part.
Best at: transparent rigid PVC — films, blister packaging, clear bottles, decorative sheet
Typical loading: 5–12 phr
Where you use it: clear films, shrink film, cosmetic packaging
Start with the question that actually matters: what does your product absolutely need?
| Your priority | Best choice | Why |
| Low-temperature impact, outdoor durability, tight budget | CPE 135A | Highest toughness-per-dollar; excellent weatherability |
| High line speed, foam cell control, surface defects | ACR (processing aid) | Fixes rheology; pair with CPE for toughness |
| Transparency + impact strength | MBS | Index-matched core-shell; stays crystal clear |
| Impact strength + transparency, moderate budget | CPE + a little MBS | Cuts MBS cost while keeping most clarity |
| General rigid PVC (pipes, fittings, profiles) | CPE 135A | The standard, proven choice |
This is where most guides go vague. Here is the honest picture:
CPE 135A is the lowest-cost impact modifier per phr of toughening — why it dominates pipes, fittings, and profiles.
ACR is priced higher per kg, but you use far less of it (1–5 phr vs 6–12 phr), so the formulation cost impact is often smaller than it looks. It also pays for itself in lower scrap and faster line speed.
MBS is the most expensive of the three. You only pay for it when transparency is non-negotiable.
The mistake to avoid: buying MBS (or an expensive AIM) for an opaque pipe because "impact modifier is impact modifier." You are paying 2–3× for transparency you will never see.
| Symptom on your line | Likely culprit | Fix |
| Foam board cells collapsing at high speed | Low melt strength | Add high-MW ACR |
| Pipe/profile cracking in cold weather | Insufficient low-temp impact | Increase CPE 135A or switch to higher-grade CPE |
| Rough surface, melt fracture, sharkskin | Poor fusion / die buildup | Add ACR processing aid |
| Clear film going cloudy when you add modifier | Wrong modifier type | Switch to MBS |
| Part is fine but cost is too high | Over-specified modifier | Drop to CPE 135A, or blend CPE+MBS |
If you only remember one thing from this article, make it this:
CPE 135A for toughness and cost; ACR for process and surface; MBS only when you need to see through it.
Most rigid PVC formulations are CPE 135A + a small amount of ACR processing aid. That combination solves the vast majority of real-world production problems without over-spending. Reserve MBS for transparent applications, and reserve high-load ACR for high-speed foam and WPC lines.
Yes — and you usually should. CPE 135A handles impact toughness, while ACR fixes melt strength and surface finish. They target different failure modes, so combining them gives you both benefits without double-counting cost.
Usually not. Try reducing your current modifier loading, or blending a small percentage of MBS with CPE 135A first. You will often recover most of the clarity at a fraction of the full-MBS cost.
No — CPE itself has excellent weatherability, which is why it is standard in window profiles and outdoor pipes. Pair it with a proper stabilizer system and it performs reliably outdoors.
Ask for chlorine content (35–36% is standard for impact modification), consistent molecular weight, and low gel/residue. High-purity CPE disperses evenly and will not create surface specks or stress concentrations.
Start with CPE 135A at 6–10 phr plus a small amount of ACR processing aid. That is the safest, most cost-effective baseline for most rigid products; adjust once you see real production data.
Choosing a PVC impact modifier is not about finding the "best" additive — it is about matching the additive to your product's one non-negotiable requirement: outdoor toughness, processing speed, or transparency. Once you know that priority, the choice is usually obvious, and it usually starts with CPE 135A.
Weifang Fine New Material Co., Ltd. is a PVC additive and chlorinated polymer supplier based in Weifang, Shandong, China. We supply high-stability CPE 135A, high-molecular-weight ACR processing aids, PVC stabilizers, and CM/CSM rubber to 40+ countries, with formulation support tailored to your production standard.
Need help choosing between CPE, ACR, and MBS for your specific product? Contact our technical team for a formulation recommendation, or request a product datasheet.
INQUIRE IMMEDIATELY